Viton vs Silicone Valve Seals: Picking the Elastomer That Fits the Service

The Short Answer

Viton (FKM) and silicone (VMQ) seals fail in opposite directions, so the service decides the choice rather than the price. FKM holds its shape in mineral oil, fuel, and many aromatic solvents and runs continuously to roughly 200 °C, which is why hydrocarbon lines standardize on it. Silicone keeps flexibility far below freezing, near -60 °C for general-purpose compounds, and tolerates dry heat, ozone, and water, but it swells heavily in oil and has low tear strength. Lines carrying oil, fuel, or solvent call for FKM; cold lines, water service at moderate temperature, and seals that need a soft, low-force seat call for silicone.

What Viton (FKM) Actually Is

Viton is a brand name for fluoroelastomer, or FKM. The fluorine in the polymer backbone is the reason hydrocarbons have little effect on it: the bond energy is high enough that oil and fuel molecules do not pull the chain apart. General-purpose compounds sit around 70 Shore A and hold continuous service from about -20 °C to 200 °C; higher-temperature grades exist, and the exact limit belongs to the specific compound datasheet rather than the family name.

The limits are equally specific. FKM is a poor choice for hot water and steam over long exposure, for low-temperature flexing, and for low-molecular esters, ketones, ammonia, and some brake fluids. It also costs several times what silicone costs, which matters on a valve with four seats and a bonnet gasket.

What Silicone (VMQ) Actually Is

Silicone rubber is a polysiloxane, and its wide working band comes from the flexibility of the Si-O backbone. General-purpose VMQ runs from roughly -60 °C to 200 °C, stays elastic after long cold exposure, and shrugs off ozone, weathering, and most aqueous service. That combination makes it the default for outdoor lines, cold rooms, and low-temperature test rigs.

The mechanical side is where silicone gives ground. Tensile and tear strength are low, abrasion resistance is poor, and mineral oil, diesel, and many solvents cause large volume swell. A silicone O-ring that looks fine on the bench can extrude or nibble at a high-velocity seat within weeks.

Side-by-Side Comparison

Property FKM (Viton) Silicone (VMQ)
Typical continuous temperature range About -20 °C to 200 °C About -60 °C to 200 °C
Flexibility below freezing Stiffens; not preferred Retains elasticity
Volume swell in mineral oil and fuel Low High
Hot water and low-pressure steam Not preferred for long exposure Fair in water; limited in steam
Tear and abrasion resistance Good Low
Ozone, weathering, outdoor aging Good Excellent
Compression set at moderate temperature Low Moderate
Relative material cost High Low
Typical hardness range 70 Shore A common 50 to 70 Shore A common

The values above describe general-purpose compounds and are intended for screening, not for approval. A specific grade can shift the temperature ceiling by tens of degrees; data needs further verification against the supplier datasheet before a seal is released into a hydrocarbon or steam line.

Advertise Here - sponsor this article

Advertise with Valve Knowledge Hub · liujinghui1987@163.com · $150/month

Where the Decision Usually Turns

Most real decisions are made by one or two service details rather than by the table. A fuel-oil train with a modulating control valve will see aromatic components and 80 °C to 120 °C metal temperature; FKM is the routine answer there, and silicone would swell and drag on the plug stem. A chilled-water coil header in an unheated plant room that dips to -25 °C in winter is the reverse case: FKM seats go hard and lose resilience at startup, while silicone stays soft and seals on the first stroke.

The difficult middle ground is hot water above about 90 °C and low-pressure steam. Neither elastomer is a comfortable long-term fit there, and the practical route is EPDM for water or a PTFE-faced seat for steam, which is a materials decision covered in valve seat materials explained. Comparing FKM with EPDM and nitrile for the same water and air duties is worth doing before locking the specification, since the swell behavior differs in ways the temperature table does not show; see EPDM vs Buna-N valve seat.

Compatibility Traps That Trigger a Retest

Four traps account for most field surprises with these two materials. Amine-based corrosion inhibitors and some glycol blends attack FKM more than the base fluid does. Silicone absorbs silicone oil and silicone-based lubricants used on adjacent assemblies, which can soften it. Compressor lubricants with high aromatic content swell silicone badly. And low-pressure steam that looks harmless on a data sheet will shorten both materials once cycling condenses water on the seat.

Compression set deserves its own check because it decides how the seal behaves after a year of cycling rather than on the day it is fitted. FKM compounds generally recover well after long hot service, which is why they survive bonnets that are only opened at major overhauls. Silicone recovers less predictably above about 120 °C, and a silicone seat that has taken a set will weep at low differential even though it looked tight at commissioning. On cold service the picture reverses: silicone stays elastic through repeated freeze-thaw, while FKM can crack at the seat edge if it is flexed far below its normal range during a winter startup.

Purchasing habits follow the same split. Plants that run both materials tend to standardize silicone for utility water and instrument air and keep FKM only for hydrocarbon trains, because FKM shelf life and unit cost make broad stocking expensive. Marking the seal face with the polymer code helps, since both look like black rings once they are out of the bag during a shutdown.

How to Write It on the Specification

A purchase order that says only “Viton seal” invites substitution. Naming the family (FKM or VMQ), the hardness, the ASTM D2000 line callout, and the temperature and media it faces gives the supplier a target. Where the valve is in potable water or food contact, the certification line matters more than the polymer name.

Bottom Line

Pick FKM when the seal meets oil, fuel, solvent, or a metal temperature above 100 °C. Pick silicone when the seal meets cold, water, ozone, or a soft seating requirement. When the duty is hot water or steam, neither family is the strongest answer, and the time spent checking EPDM or PTFE is usually cheaper than the retest after a failed seal.

This article provides general educational knowledge only and is not professional engineering advice.

Sources & Further Reading: ASTM (D2000 rubber specification), API.

© 2026 Valve Knowledge Hub. All rights reserved.

Disclaimer: This article is provided for general educational and informational purposes only and does not constitute professional engineering advice. Valve applications vary with pressure, temperature, media, and applicable codes. Always verify specifications against the manufacturer’s data sheet and consult a qualified engineer before selecting, installing, or repairing any valve. Valve Knowledge Hub makes no warranties about the accuracy or completeness of the information on this site and assumes no liability for any use of it.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top